series amepr5-az up to 1a | ac-dc / dc-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.l 1 of 3 north america only features: models single output model max output power (w) output voltage range (v) output current (a) input voltage (vac/hz) input voltage (vdc) efficiency (%) 115 vac 230 vac amepr5-1630az 4.8 8-16 0.3 90-264/47-440 130-370 79 75 amepr5-1435az 4.9 6-14 0.35 90-264/47-440 130-370 77 74 amepr5-1236az 4.32 5-12 0.36 90-264/47-440 130-370 77 74 amepr5-0670az 4.2 2-6 0.7 90-264/47-440 130-370 76 73 amepr5-05100az 5 3-5 1 90-264/47-440 130-370 74 72 exceeding the maximum output power will permanently damage the converter note: aimtec limited warranty of 5 years is valid based on product operation at dat asheet specifications at ambient temperature of 25c, humidity<75%, nominal input voltage (115/230vac) and at rated output load unless otherwise specified. see http://www.aimtec.com/terms- sale amepr5-az?s ac/dc led drivers have electrical safeguards designed within to protect it from conventional electrical abnormaliti es with the levels listed in the safety table. applications for use within rural agricultural, heavy industrial, and other areas or re gions which are prone to ?dirty? electrical conditions which would subject any of the above models to excessive voltages surges or spikes, may damage or cause early life failure of product. in this case consideratio n should be made by the end user to ensure that adequate line or mains surge suppression is installed in front of aimtec device to ensure t he longevity of the products. failure to identify excessive line surges violations prior to installation may damage sensitive equipment permanently. input specifications parameters conditions typical maximum units inrush current <2ms 115vac 15 a 230vac 30 leakage current 115vac 0.2 ma 230vac 0.25 ac current 115vac 0.09 a 230vac 0.06 no load consumption 115vac 0.1 w 230vac 0.2 external fuse 250v/0.5a start up time 140 ms output specifications parameters conditions typical maximum units current accuracy 10 % line regulation ll-hl 5 % load regulation 0-100% load 10 % ripple & noise 6/12/14/16v models 5v model 100 150 mv p-p hold-up time 2 ms minimum load voltage see the models table ripple and noise are measured at 20mhz bandwidth by using a 0.1 f (m/c) or (c/c) and 220f (e/c) parallel capacitor. ? ac-dc or dc-dc constant current led driver ? ? input range 90-264vac/47-440hz ? ? operating temperature 0 to 80c ? high efficiency up to 79% ? ? 5 years limited warranty click on series name for p roduct info on aimtec.com
series amepr5-az up to 1a | ac-dc / dc-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.l 2 of 3 north america only isolation specifications parameters conditions typical maximum units tested i/o voltage 3sec 3000 vac isolation resistance >1000 m ? general specifications parameters conditions typical maximum units switching frequency 65 khz over load protection 103 % over voltage protection 103 % short circuit protection auto recovery operating temperature with derating over 50c 0 to +80 o c maximum case temperature 100 o c storage temperature -40 to +95 o c temperature coefficient 0.02 % / o c cooling free air convection humidity 95 % rh case material plastic potting epoxy (ip67 rated) wires ul1015 22awg * 10cm weight 25 g dimensions (l x diameter) 29 x 26.5 mm (1.14x1.04 inch) mtbf >400,000 hrs (mil-hdbk-217f at +25c) environment approval test parameters conditions shock wave form half sine wave acceleration amplitude 5gn bump duration 30ms converter operation before and after test, body mounted (on chassis) number of bumps 18 (3 in each direction for every axis) vibration test mode sweep sine, 10-100hz, speed 0.05hz/s displacement 1 mm acceleration 3g, 3 loops 30min one cycle, 3h total, every axis tested converter operation before and after test, body mounted (on chassis) safety specifications parameters agency approvals culus, ce, fcc standards en61347-1, en61347-2-13, iec62384, ul8750, ul60950- 1, en55015, en55024, fcc part 15 subpart b, class b, ansi c63.4 :2003 harmonic current emissions iec/en 61000-3-2, (en60555-2) voltage fluctuations and flicker iec/en 61000-3-3, (en60555-3) electrostatic discharge immunity iec 61000-4-2 level 3 rf, electromagnetic field immunity iec 61000-4-3 level 2 electrical fast transient/burst immunity iec 61000-4-4 level 2 surge immunity iec 61000-4-5 level 1 rf, conducted disturbance immunity iec 61000-4-6 level 2 power frequency magnetic field immunity iec 61000-4-8 level 2 voltage dips, short interruptions immunity iec 61000-4-11
series amepr5-az up to 1a | ac-dc / dc-dc led driver www.aimtec.com tel: +1 514 620 2722 toll free: + 1 888 9 aimtec (924 6832) f 052.1e r3.l 3 of 3 north america only dimensions temperature graph -20 020406080 100 100 80 60 40 20 0 50 o c safe operating area free air convection ambient temperature o c output power % note: 1. datasheets are updated as needed and as such, specifications ar e subject to change without notic e. once printed or downloaded , datasheets are no longer controlled by aimtec; refer to www.aimtec.com for the most current product specifications. 2. product labels shown, including safety agency cert ifications on labels, may vary based on the date manufactured. 3. mechanical drawings and specifications are for reference only. 4 . all specifications are measured at an am bient temperature of 25c, humidity<75%, nominal input voltage and at rated output load unless otherwise specifie d. 5. .aimtec may not have conducted destructive testing or chemical analysis on all internal components and chemicals at the time of publishing this document. cas numbers and other limited information are considered proprietary an d may not be available for release. 5. this product is not designed for use in critical life support systems, equipment used in hazardous environments, nuclear control sys tems or other such applications which necessitate specific safety and regulatory standards ot her the ones listed in this datasheet.
|
